EXCELLENTSCORES

Wood Shop Safety Test Study Guide Complete Questions with 100% Correct Answers What is the margin of safety? 4 inches. When using a saw, never... Feed the material faster than the saw blade can remove the wood easily. The palm sander is used for what? removing small amounts of material slowly. All small work should be secured with what? A clamp or vise. Make all adjustments on all power tools with the power off, except... When adjusting the speed of the lathe. Always cut.. Away fro...

Woodshop Safety Test Answers|Complete Questions with Correct Answers Safety instructions must be given before you are allowed to work on or operate any machine or tool You are not permitted to work on any equipment or machine if the ____________________ is not present instructor Guards and safety devices must be on all machines during operation Machinery must not be oiled or adjusted while in use A machine must be started and stopped only by the operator Do not leave a machine while i...

Woodshop Final Exam Review |Graded A+ Margin of Safety: Table Saw 4" Margin of Safety: Radial Arm Saw 6" Margin of Safety: Band Saw 2" Margin of Safety: Jointer 4" Margin of Safety: Planer N/A Margin of Safety: Sanders N/A Margin of Safety: Chop Saw 4" How to square a board: 1. Joint one edge 2. Rip board to desired width 3. Trim one end 4. Measure cut opposite end to desired length Board feet (all inches) T"xW"xH"/144 Board feet (height in feet) T"xW"xH'/12 T ...

Wood Shop Safety Test Review |Complete Questions with 100% Correct Answers Safety is the condition of being safe from risk or danger True Which of the following is NOT a helper to feed stock into a machine Straight edge Device that detects leaks to the ground and breaks an electric circuit GFCI This describes ingredients in materials, health hazards, and precautions to take MSDS This is an organization that establishes regulations about hazardous waste EPA This is an organization th...

Woodshop quiz Wih 100% Correct Answers What is the primary purpose of sanding? to prepare the wood surfaces by removing obstacles(milling marks, burnished wood) to the acceptance of stains and finishes. What must you do to prepare the project BEFORE APPLYING stain and finishes? 1. Fill imperfections such as holes and cracks with wood filler and sand smooth. 2. Sand and seal end grade with wood conditioner. 3. Properly sand(with the grain and with multiple grits of sandpaper-medium to fine)...

Woodshop Exam Review Questions With Correct Answers Graded A+ Back Saw A saw with very fine teeth and is often used in a miter box for cutting angles. The thin blade is reinforced with a ridge of thicker metal along the back of the saw. It cannot cut deeper than the ridge. Band Saw A machine tool with endless blade that travels around two pulleys and is used to cut thin or thick stock of wood in curve or straight form. Beading Bit Belt Sander A sanding machine on which the abrasive coati...

Woodshop Test Questions With 100% Correct Answers Safety instructions must be given before allowed to work/operate on any machine or Tool You're not permitted to work on any equipment/machine if the instructor is not Present Guards and safety devices must be on all machines during Operation Machinery must not be oiled or adjusted while in Use A machine must be started and stopped only by the Operator Do not leave a machine while it is Running When working on or near any machine or ...

Electrolysis IBEC+Laser STATE BOARD Practice test 2023 Questions with Correct Answers|UPDATED 2024 !!! Laser stands for what? Light Amplification by Stimulated Emission of Radiation What is the distance measured in nanometers between two peaks or two troughs known as? Wavelength Light of only one color & one specific wavelength is known as? Monochromatic Refraction is also known as what? Transmission The process where by a newly created photon of light (generated through amplificati...

DOT CERTIFICATION EXAM REVIEW|Questions with Correct Answers .Graded A+ Medical Examiners A person who is licensed, certified, and or registered in accordance with applicable state laws and regulations, to perform physical examinations Motor carrier employees Responsible for hiring, supervising, training, assigning, or dispatching of drivers and employees concerned with the installation, inspection, and maintenance of motor vehicle equipment and or accessories. Medical Review Officer (MRO) ...

DOT Certification Medical Examiner Test|Complete Questions with 100% Correct Answers Coronart Bypass Graft Qualified for one year once 3 months post procedure if a symptomatic, LVEF >40% and meets general requirements CHF accompanied by dyspnea at rest? DQ; not medically fit for duty Unstable angina DQ Qualify post pneumothorax-when? Qualify when FEV >65% Psychological assessment 1.) suspicious behavior 2.) hallucinations 3.) signs of flat affect Purpose of CMV physical exam ...